LMS – Multiple loader manager

Introduction #

This document describes the specifications of BLACK ACCESS terminals (WB-BA-07S-SS and WB-BA-22S-SS), and how to install and set up your terminal.

To help you better understand and use this product, the user manual provides a detailed introduction to the functions, installation, operation and maintenance of the BLACK ACCESS bollards (WB-BA-07S-SS and WB-BA-22S-SS). This manual is essential for installation, supervision, debugging and maintenance.

We sincerely hope that this product will meet your needs, so please do not hesitate to send us your comments and suggestions on the performance and functions of our products. We are constantly improving the quality of our products and services.

Product presentation #

Backlit status/logo indicator
Wall-mounting bracket
On / off / emergency stop button
Plug

Packing list #

N°	Items	Qty.
1	EV terminal	1
2	Link to user manual	1
3	Quality certificate	1
4	Mounting bracket	1
5	ST6.3*40 stainless steel self-drilling hex head screws	4
6	12*46 plastic expansion plugs	4

Installation and wiring #

Wall installation #

Open the packaging, and you’ll find a charging station, its mounting bracket, a link to the user manual and a bag of mounting accessories.
Remove the mounting bracket from the charging station and use it as a template to mark the position of the drill holes. Drill the holes and insert the expansion plugs supplied in the accessory bag. Then fix the mounting bracket to the wall.

Open the packaging and you’ll find a charging station, its mounting bracket, a link to the user manual and a bag of mounting accessories.

Pole-mounted installation (WB-P1) #

You can install your BLACK ACCESS bollard on a WB-P1 mounting post (sold separately). The post must be installed on a hard surface, a concrete surface is recommended, but it can also be mounted on solid ground. Drill the holes according to the requirements shown in the illustration, and insert the expansion plugs.

Secure the post to the holes with the bolts. The input cables should be inserted into the post from the lower central area and brought out via the area below the cable hook, plugged with a rubber insert.

Secure the post to the holes with the bolts. The input cables should be inserted into the post from the lower central area and brought out via the area below the cable hook, plugged with a rubber insert.

Wiring #

Crimp the ferrule or insulated ring terminals shown below to the end of the AC input wires. Connect the wires to the load point housing as shown below. Check wiring, then snap RCBO into side window. Unscrew the side cover plate, and the wiring is complete.

	Power output	L1	L2	L3	N	PE
Terminal	7.4kW	Red	X	X	Blue	Yellow & Green
Cable	7.4kW	≥10mm² ≥AWG7	X	X	≥10mm² ≥AWG7	≥10mm² ≥AWG7
Terminal	22kW	Red	Black	Grey
Cable	22kW	≥10mm² ≥AWG7	≥10mm² ≥AWG7	≥10mm² ≥AWG7	≥10mm² ≥AWG7	≥10mm² ≥AWG7

Parameter settings #

Once installation and wiring are complete, connect the charger to a computer and configure the settings via the computer’s web browser. The charger is ready for use by default, but it is recommended that you put it online (remote diagnostics, change of charging mode, charging reports, etc.).

Settings via the Wellborne Plus application #

To access your terminal’s settings with the Wellborne Plus application, please refer to our Wellborne Plus application page, in the “Charger settings” section.

Setup via your computer #

To access your terminal settings with your PC (Windows 10 & 11) or Mac, please refer to our Technical Brochure page, chapter “Setting Wellborne product parameters via a computer“.

The different charging modes of your terminal #

There are three operating modes for your Wellborne charging station: APP, RFID and Plug & Charge.

APP mode (third-party system operation: APP/RFID) #

With the WB Charge application, you can start or stop a charge, manage authorized users, tariffs and more. For more information on how to use the WB Charge application, please refer to the WB Charge application.

RFID mode #

In RFID mode, charging can only be initiated by swiping an RFID card over the terminal’s reader. For more information on how to set up your reader/configurator and RFID cards, please refer to our Technical Brochure, chapter “RFID card configurator“.

Plug & Charge mode #

Plug & Charge mode enables you to start charging a vehicle as soon as it is connected to your charging station. If you wish to interrupt charging, simply press the on/off button above the T2 socket.

Anomalies #

Troubleshooting #

In the event of a fault, users can check the information indicated by the LED. Each fault is indicated by a number of flashes and a color. If several faults occur at the same time, each sequence is displayed in chronological order at 3-second intervals. To find out more about diagnosing faults on your terminal, please refer to the “AC Fault Diagnostics” page.

Firmware update failure with microSD card #

Check if the capacity is greater than 4GB, please use a microSD card with a capacity of less than 4GB to try again.
Check that the SD card is formatted with FAT32.
Check that the allocation unit value is 4096.
Check that the firmware file has been renamed “App.bin”.
Check that you have set “state = 1” in the “UpIoadConfig.txt” file.

Failed firmware update with a computer #

Please try with your browser, or restart the laptop to try again.

Dynamic energy control & solar management #

For dynamic energy control and solar management of your bollard via the application, PC or Mac, please refer to our page “Setting Wellborne product parameters via the WB Charge application“, or “Accessing Wellborne product parameters via a computer“.

Technical specifications #

BLACK ACCESS SOLO 7.4 kW (WB-BA-07S-SS)

SPECIFICATIONS	WB-BA-07S-SS
IN & OUT
Input voltage	230V AC
Input frequency	50/60 Hz
Output voltage	230V AC
Max. output power	7.4kW
Max. output current	32A
Load interface type	IEC 62196-2, Type 2S / IEC 61851-1
Connection	Standard socket
Cable length	–
Number of connections	1
PROTECTION
Overvoltage protection	No
Protection against undervoltage	No
Overload protection	No
Short circuit protection	No
Earth leakage protection	No
Overheating protection	No
Lightning protection	No
FUNCTIONS & ACCESSORIES
Ethernet / WIFI / 4G	Yes / Yes / Opt
LCD	No
RCD	DC 6mA
Access control	APP / Plug & Charge
LED indicator	Yes
Emergency stop button	No
Intelligent power control	Yes
Pro-earth	Yes
Installation	Wall-mounted / Free-standing (opt.)
MID metering	No
WORKING ENVIRONMENT
Protection class	IP65
Shock resistance	IK10
Operating temperature	-25°C ~+50°C
Relative humidity	5%-95% non-condensing
Maximum altitude	<2000 m
Cooling	Natural air cooling
Standby power consumption	<8W
MECHANICS
Dimension (W / H / D)	246 / 382 / 162
Weight (kg)	3 kg
Packaging dimensions (W / H / D)	–
CERTIFICATIONS
Certificate	CE

BLACK ACCESS SOLO 22 kW (WB-BA-22S-SS)

SPECIFICATIONS	WB-BA-22S-SS
IN & OUT
Input voltage	400V AC
Input frequency	50/60 Hz
Output voltage	400V AC
Max. output power	22kW
Max. output current	32A
Load interface type	IEC 62196-2, Type 2S / IEC 61851-1
Connection	Standard socket
Cable length	–
Number of connections	1
PROTECTION
Overvoltage protection	No
Protection against undervoltage	No
Overload protection	No
Short circuit protection	No
Earth leakage protection	No
Overheating protection	No
Lightning protection	No
FUNCTIONS & ACCESSORIES
Ethernet / WIFI / 4G	Yes / Yes / Opt
LCD	No
RCD	DC 6mA
Access control	APP / Plug & Charge
LED indicator	Yes
Emergency stop button	Yes
Intelligent power control	Opt
Pro-earth	Yes
Installation	Wall-mounted / Free-standing (opt.)
MID metering	No
WORKING ENVIRONMENT
Protection class	IP65
Shock resistance	IK10
Operating temperature	-25°C ~+50°C
Relative humidity	5%-95% non-condensing
Maximum altitude	<2000 m
Cooling	Natural air cooling
Standby power consumption	<8W
MECHANICS
Dimensions (W / H / D)	246 / 382 / 162 mm
Weight (kg)	3.5 kg
Packaging dimensions (W / H / D)	–
CERTIFICATIONS
Certificate	CE